diff options
Diffstat (limited to 'net-scripts')
| -rw-r--r-- | net-scripts/conf.d/net.example | 76 |
1 files changed, 75 insertions, 1 deletions
diff --git a/net-scripts/conf.d/net.example b/net-scripts/conf.d/net.example index 42bc2e3..8a5078c 100644 --- a/net-scripts/conf.d/net.example +++ b/net-scripts/conf.d/net.example @@ -337,9 +337,83 @@ # need net.eth0 net.eth1 #} + +#----------------------------------------------------------------------------- +# PPP +# For PPP support, emerge net-dialup/ppp +# PPP is used for most dialup connections, including ADSL. +# The older ADSL module is documented below, but you are encouraged to try +# this module first. +# +# You need to create the PPP net script yourself. Make it like so +#cd /etc/init.d +#ln -s net.lo net.ppp0 +# +# Each PPP interface requires an interface to use as a "Link" +#link_ppp0="eth0" # PPPoE requires an ethernet interface +#link_ppp0="/dev/ttyS0" # Most PPP links will use a serial port +# +# PPP requires at least a username. You can optionally set a password here too +# If you don't, then it will use the password specified in /etc/ppp/*-secrets +# against the specified username +#username_ppp0="user" +#password_ppp0="password" +# +# The PPP daemon has many options you can specify - although there are many +# and may seem daunting, it is recommended that you read the ppp man page +# before enabling any of them +#pppd_ppp0=( +# "debug" # Enables syslog debugging +# "noauth" # Do not require the peer to authenticate itself +# "defaultroute" # Make this PPP interface the default route +# "userpeerdns" # Use the DNS settings provided by PPP +# +# On demand options +# "demand" # Enable dial on demand +# "idle 30" # The link will go down after 30 seconds of inactivity +# "10.112.112.112:10.112.112.113" # Phony IP addresses +# "ipcp-accept-remote" # Accept the peers idea of remote address +# "ipcp-accept-local" # Accept the peers idea of local address +# "holdoff 3" # Wait 3 seconds after link dies before re-starting +# "lcp-echo-interval 15" # Send a LCP echo every 15 seconds +# "lcp-echo-failure 3" # Make peer dead after 3 seconds of in-activity +# +# Compression options - use these to completely disable compression +# "noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp" +# +# Dial-up settings +# "lock" # Lock serial port +# "115200" # Set the serial port baud rate +# "modem crtscts" # Enable hardware flow control +# "192.168.0.1:192.168.0.2" # Local and remote IP addresses +#) +# +# Dial-up PPP users need to specify a telephone number +#phone_number_ppp0=( "12345689" ) +# They will also need a chat script - here's a good one +#chat_ppp0=( +# 'ABORT' 'BUSY' +# 'ABORT' 'ERROR' +# 'ABORT' 'NO ANSWER' +# 'ABORT' 'NO CARRIER' +# 'ABORT' 'NO DIALTONE' +# 'ABORT' 'Invalid Login' +# 'ABORT' 'Login incorrect' +# 'TIMEOUT' '5' +# '' 'ATZ' +# 'OK' 'AT' # Put your modem initialization string here +# 'OK' 'ATDT\T' +# 'TIMEOUT' '60' +# 'CONNECT' '' +# 'TIMEOUT' '5' +# '~--' '' +#) + #----------------------------------------------------------------------------- # ADSL -# For ADSL support, emerge net-dialup/rp-pppoe +# For ADSL support, emerge net-dialup/rp-pppoe +# WARNING: This ADSL module is being deprecated in favour of the PPP module +# above. # You should make the following settings and also put your # username/password information in /etc/ppp/pap-secrets |